There is little that gives more pride than being able to show off your yard after a great landscaping job was done. Some people compete or are rewarded by having the best flowers or yard in the neighborhood. One way to help make it look great is by using plastic bender board to create very nice landscaped areas between the flowerbeds and the grass. Using this material will keep weeds and grass from encroaching on the flowerbeds or other decorations and is environmentally sound as well.
Two different types exist and are in use today. The first is made from packed wood fibers and other natural materials. Though it is a great way to create the border, it will have to be replaced over time because it is designed to decay and work its way into the soil. The plastic type will not decay over time and is environmentally sound because it is made of recycled plastics that would be headed to the landfill. It will last much longer and keep doing its job for years.
First, figure out how much you need. The easiest procedure is to put a few stakes in the ground along the path you will take. Run a length of string between the stakes and then measure the string. This way you won't have to use an inflexible measuring tape along the bending path and take your best guess. If you want to be sure, add a few inches to the measurement since you can cut off what you don't need.
The second step is to dig a trench. You will want to dig it six inches wide to accommodate the bender board. If you want the board to be covered with dirt, make sure the trench is deep enough to do so. Keep the dirt nearby because you will use it to fill in the trench after you have placed the material for the border.
After digging, start putting in the stakes. You should have several to help hold the board in place. As you hammer them in with your rubber mallet, make sure they are placed so the material will sit on the turf side of the stakes. This will keep the grass from growing where it shouldn't.
Now you're ready to put it in the ground. Roll the border out and place it next to the trench. Once it is ready, simply slide or roll it in and start attaching it to the stakes. Start at one end and be sure it all sits below the surface since you want to bury it.
The last step is to fill in the trench. Using the dirt you set aside in step two, fill in the hole. Since you have the border in the hole already you should have dirt left over. Use it to pack in the border well since rain or watering will cause the dirt to settle. Having a bit of a mound along the path is best in the beginning so it can settle properly.
Now you are done. You have successfully placed a border between your grass and other landscaping. This will help keep the weeds out and let you avoid mowing up into the flowerbeds. The border will help prevent weeds and provide the needed separation between the beds and the grass.
Two different types exist and are in use today. The first is made from packed wood fibers and other natural materials. Though it is a great way to create the border, it will have to be replaced over time because it is designed to decay and work its way into the soil. The plastic type will not decay over time and is environmentally sound because it is made of recycled plastics that would be headed to the landfill. It will last much longer and keep doing its job for years.
First, figure out how much you need. The easiest procedure is to put a few stakes in the ground along the path you will take. Run a length of string between the stakes and then measure the string. This way you won't have to use an inflexible measuring tape along the bending path and take your best guess. If you want to be sure, add a few inches to the measurement since you can cut off what you don't need.
The second step is to dig a trench. You will want to dig it six inches wide to accommodate the bender board. If you want the board to be covered with dirt, make sure the trench is deep enough to do so. Keep the dirt nearby because you will use it to fill in the trench after you have placed the material for the border.
After digging, start putting in the stakes. You should have several to help hold the board in place. As you hammer them in with your rubber mallet, make sure they are placed so the material will sit on the turf side of the stakes. This will keep the grass from growing where it shouldn't.
Now you're ready to put it in the ground. Roll the border out and place it next to the trench. Once it is ready, simply slide or roll it in and start attaching it to the stakes. Start at one end and be sure it all sits below the surface since you want to bury it.
The last step is to fill in the trench. Using the dirt you set aside in step two, fill in the hole. Since you have the border in the hole already you should have dirt left over. Use it to pack in the border well since rain or watering will cause the dirt to settle. Having a bit of a mound along the path is best in the beginning so it can settle properly.
Now you are done. You have successfully placed a border between your grass and other landscaping. This will help keep the weeds out and let you avoid mowing up into the flowerbeds. The border will help prevent weeds and provide the needed separation between the beds and the grass.
About the Author:
When you are looking for information about plastic bender board, come to our web pages online today. More details are available at http://www.bestedging.com now.
No comments:
Post a Comment