Water loss is expected to happen from a swimming pool or a spa at some point when they are in use. Normally, the loss of water from the structure in subject takes place in three main ways, namely, backwashing the filters, evaporation, and splash out. Water loss can be significant to people who stay in arid regions. This is what Queen Creek pool service is all about.
Because of the sources of loss of water named above, it is normal to add at least two inches of water to the structure every week. However, had to add more than two inches of water to the structure within a week, it may be a reason to suspect that a leak exists. This is true especially if no reason exists for change in the rate of water loss.
For example, one should understand that evaporation rates keep on changing depending on what season of the year it is. Also, in case the use of the pool has risen recently, it implies that water loss will increase as well. In case none of these activities have happened in the recent past and yet water loss is happening at a faster rate, one ought to be suspicious.
Before one decides to go further to contact a local pool technician, it is vital to confirm the suspicions one has. Several techniques can be employed to ascertain if indeed a leak actually exists. To confirm the presence of a leak, one should begin by inspecting the obvious. For example, one should make sure the leakage is not located at the equipment.
To ensure equipment is not leaking, one should take a close look at the pipe valves, pump, heater, and filter. One should also check the ground around the structure to ensure that it is not wet. One should walk around the structure to determine if there are any eroding or sunken areas. If all these seem to be okay, then it is time for the next step.
An alternative technique that can be employed to establish whether the structure is leaking is marking the water level inside the structure at the skimmer. This is made possible by use of grease, tape or pencil. Allow the pool a duration of 24 hours prior to coming back to assess the new level of the water.
An ordinary pool should lose about a quarter an inch of water each day. In case the drop in the level of water is higher than a quarter an inch, this could mean that a leak exists. Another way is to use a bucket with water filled to a similar level as the level in the structure. The bucket ought to be placed on top of the steps used when entering the structure.
The bucket has to be given a duration of 24 hours, after which one should check it. If the level of water in the pool has gone below the height of water in the bucket, then this is confirmation of the presence of a leak. Because the water in both the structure and the bucket are subjected to evaporation, the rate of water loss ought to be the same.
Because of the sources of loss of water named above, it is normal to add at least two inches of water to the structure every week. However, had to add more than two inches of water to the structure within a week, it may be a reason to suspect that a leak exists. This is true especially if no reason exists for change in the rate of water loss.
For example, one should understand that evaporation rates keep on changing depending on what season of the year it is. Also, in case the use of the pool has risen recently, it implies that water loss will increase as well. In case none of these activities have happened in the recent past and yet water loss is happening at a faster rate, one ought to be suspicious.
Before one decides to go further to contact a local pool technician, it is vital to confirm the suspicions one has. Several techniques can be employed to ascertain if indeed a leak actually exists. To confirm the presence of a leak, one should begin by inspecting the obvious. For example, one should make sure the leakage is not located at the equipment.
To ensure equipment is not leaking, one should take a close look at the pipe valves, pump, heater, and filter. One should also check the ground around the structure to ensure that it is not wet. One should walk around the structure to determine if there are any eroding or sunken areas. If all these seem to be okay, then it is time for the next step.
An alternative technique that can be employed to establish whether the structure is leaking is marking the water level inside the structure at the skimmer. This is made possible by use of grease, tape or pencil. Allow the pool a duration of 24 hours prior to coming back to assess the new level of the water.
An ordinary pool should lose about a quarter an inch of water each day. In case the drop in the level of water is higher than a quarter an inch, this could mean that a leak exists. Another way is to use a bucket with water filled to a similar level as the level in the structure. The bucket ought to be placed on top of the steps used when entering the structure.
The bucket has to be given a duration of 24 hours, after which one should check it. If the level of water in the pool has gone below the height of water in the bucket, then this is confirmation of the presence of a leak. Because the water in both the structure and the bucket are subjected to evaporation, the rate of water loss ought to be the same.
About the Author:
Get excellent tips on how to pick a Queen Creek pool service company and more info about a reliable company at http://www.neptunepoolsaz.com right now.
No comments:
Post a Comment